[R18+] "Times Square Lights" M4 Gel Ball Blaster [ID Check Required]

Brand: Hobby Zone

Product Code: G180-4

$69.90 69.90
  IN STOCK

To purchase this item, you must be 18 years of age or older. After completing your purchase, you will receive a Real ID check verification email in your inbox. Check all categories of your inbox, such as your spam, updates, social folders.

Specifications:

Firing Range: 10 - 12 meters

Ammo Size: 7 - 8 mm

Features:

  • Rechargeable lithium battery
  • Fully automatic firing
  • The bullets are made of water polymer, easy to break and nontoxic
  • The pattern on Gel Ball Blaster varies (may be slightly different from the image listed)

Please note that this is not a real gun. It is just a toy.

Do not use it as if it were a real gun. The cocking handle is non-functional, you cannot prime the blaster with it. The Rear Iron Sight does not work either. It is simply there for cool looking aesthetics. 

How to Load Gel Balls into a Bottom-Fed Magazine

  1. Open the Magazine Door
    Slide the loading dock door upward to open the magazine for loading.

  2. Prepare the Gel Balls
    Use hydrated gel balls that have been patted dry or sieve dried to prevent jamming or misfeeds.

  3. Fill the Magazine
    Pour the gel balls into the magazine until it’s completely full.

  4. Pre-Load the Gel Balls
    After loading, press the small triangular piece at the top of the magazine (known as the spring-loaded pusher tab) multiple times.
    This action pushes the gel balls up into the feeding channel, readying them for firing.

  5. Prime the Blaster
    Once inserted, hold down the trigger for about 5 seconds (without releasing) to allow the blaster to chamber the gel balls before your first shot.

Dimensions:

  • Length of Blaster Body: 68.5 cm
  • Length of Rear Iron Sight: 10cm
Included:
  • 1 x Bottom-fed Magazine
  • 1 x 7.4 Volt Rechargeable Battery ( 4-pin )
  • 1 x Blue Frame Safety Glasses
  • 1 x USB Charging Cable
  • 1 x Small satchel of dry Gel Balls
  • 1 x Rear Iron Sight (just for decoration)

Attaching the Nozzle and Buttstock – Gap Alignment Guide

  1. Identify the Alignment Points
    Locate the big gap and small gap on both the front nozzle and the main blaster body. These gaps are designed to interlock and ensure proper orientation.

  2. Align the Gaps
    Line up the big gap on the nozzle with the big gap on the blaster body, and do the same for the small gap.
    This step is critical — mismatched alignment may result in stress on the plastic during installation.

  3. Install with a Gentle Twist
    Once aligned, gently twist the front nozzle into place.
    Turn only in the correct direction until all the outer segments lock flush with the blaster body.

  4. Repeat for the Buttstock (if separate)
    Apply the same big-gap/small-gap alignment method when attaching the buttstock to the rear of the blaster body.

  5. Handle with Care
    ⚠️ Use extra caution during the initial twist.
    Forcing or misaligning any of the three major parts (nozzle, body, buttstock) can cause cracks or permanent damage.

To Install the Battery:

  • Open the Buttstock Flap
    Gently open the flap located at the back of the buttstock to access the battery compartment.

  • Connect the Battery
    Plug the battery into the connector inside the blaster.

  • Insert the Battery Carefully
    Slowly and carefully place the battery into the available space within the buttstock.
    ⚠️ Be mindful not to tug, pinch, or stress the wires during this step.

  • Close the Flap
    Once the battery is securely in place, close the buttstock flap.